Pennsylvania PennDOT CDL General Knowledge Practice Test 3
Test 3 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 56 correct answers to pass, the same ratio as the real Pennsylvania test.
- Questions70
- Correct to pass56
- Passing score80%
- Minimum age18 years
-
1. When must a post-trip inspection be made?
Show answer
Answer D: At the end of each day the driver operates the vehicle
The post-trip inspection closes out each driving day so that anything found is recorded before the vehicle is handed to the next driver.
-
2. How should a commercial driver treat the speed posted for a curve?
Show answer
Answer B: As a limit set for cars in good conditions, so a heavy or tall load calls for a lower speed
Posted curve speeds are based on passenger vehicles in good conditions, and a tall or heavy load can roll over well below that speed.
-
3. You are hauling livestock and the trailer is only partly full. What should be done?
Show answer
Answer A: Use false bulkheads or partitions to keep the animals bunched together
Animals that can move around shift the center of gravity, so a partial load is bunched together with partitions to limit how far the weight can move.
-
4. You are hauling an open box of loose gravel. What does that load require?
Show answer
Answer A: A cover, so that material cannot blow off or spill onto the road
Loose material that can be blown or spilled has to be covered so it does not come out of the body and strike traffic behind.
-
5. Taking your eyes off the road for about five seconds at highway speed means traveling roughly how far unseen?
Show answer
Answer A: About the length of a football field
At highway speed a five second glance away covers roughly 100 yards, which is far more road than any driver can afford to travel blind.
-
6. When should a driver select the gear for a long, steep downgrade?
Show answer
Answer B: Before starting down the grade
The low gear has to be chosen before the descent, because a heavy vehicle gaining speed may refuse to shift down at all.
-
7. What does the federal bridge formula do?
Show answer
Answer C: It reduces the weight allowed on a group of axles as those axles get closer together
Axles bunched together concentrate the load on a short span of a bridge, so the formula lowers the allowable weight as the spacing shrinks.
-
8. How is a shipping container normally secured when it is carried on a special container chassis?
Show answer
Answer B: With its own locking devices that attach the container directly to the chassis frame
Containers built for rail or ship transport have locking corners that fasten to a matching chassis; a container carried on a plain flatbed must be secured like any other cargo.
-
9. What is the correct way to test the parking brake before a trip?
Show answer
Answer C: With the parking brake set, put the vehicle in a low gear and gently try to move forward
A parking brake that holds against a gentle pull in low gear is working; if the vehicle moves, the brake needs adjustment or repair.
-
10. An oncoming vehicle drifts across the center line into your lane. What is usually the safest move?
Show answer
Answer C: Steer to the right, toward the shoulder if necessary
Moving right keeps you away from the drifting vehicle and off the oncoming side; the other driver may swerve back and hit you if you go left.
-
11. In a vehicle with a manual transmission, when should the clutch be pushed in during a normal stop?
Show answer
Answer A: Just before the engine would stall, when the vehicle is nearly stopped
Staying in gear until the last moment keeps engine braking and steady control, so the clutch goes down only when the engine is about to drop below idle.
-
12. Why does the manual insist on a firm grip with both hands on opposite sides of the steering wheel?
Show answer
Answer A: A hard bump can pull the wheel out of a loose grip
Hitting a curb or a deep pothole can jerk the wheel violently, and only a firm two-handed grip keeps the vehicle under control when that happens.
-
13. During the walkaround you notice one tire on an axle is a radial and the tire next to it is bias-ply. What should you do?
Show answer
Answer B: Treat it as a defect, because radial and bias-ply tires must not be mixed on the same axle
Radial and bias-ply tires flex and grip differently, so mixing them on one axle makes the vehicle handle unpredictably and is not allowed.
-
14. May a commercial driver use a hand-held phone while stopped at a red light?
Show answer
Answer B: No, a stop in traffic still counts as driving
Hand-held use is allowed only when the vehicle has been moved to the side of or off the highway and halted where it can safely remain stopped.
-
15. The engine has overheated and you need to check the coolant. What is the safe procedure with a pressurized radiator cap?
Show answer
Answer A: Shut the engine off, let the system cool, protect your hands, turn the cap slowly to its first stop so pressure escapes, step back, then remove it
A hot pressurized system throws steam and boiling coolant out of the opening, so the pressure is released slowly and only after the engine has cooled.
-
16. While checking the in-cab gauges after start-up, what should the coolant temperature gauge do?
Show answer
Answer C: Rise gradually to the normal operating range
A healthy cooling system warms the engine slowly; a gauge that shoots up or stays cold points to a problem with the thermostat, coolant or sensor.
-
17. At a rest area you find that the load has shifted although the straps still feel tight. What should you do?
Show answer
Answer C: Correct the load before driving on, since a shifted load is no longer secure
Movement means the securement has already failed once, and a load that has shifted can shift again, so it is put right before the vehicle moves.
-
18. Why do worn tires lose grip so quickly on a wet road?
Show answer
Answer D: Shallow tread cannot move water out from under the tire
The grooves in a tire exist to channel water away so the rubber can touch the road, and a worn tire has lost that capacity.
-
19. After two hours of driving you measure a tire and the pressure reads higher than the cold figure. What should you do?
Show answer
Answer B: Nothing, because pressure rises normally as a tire heats up in use
Air expands as the tire heats, so a higher hot reading is expected, and letting air out leaves the tire underinflated once it cools.
-
20. A vehicle becomes unsafe while you are already on the road. What does the federal rule allow?
Show answer
Answer A: Continuing only to the nearest place where repairs can safely be made
If stopping where you are would be more dangerous than moving, the rule allows you to reach the nearest place where the vehicle can safely be repaired, and no further.
-
21. Which step of the seven-step inspection method comes immediately after checking the engine compartment?
Show answer
Answer D: Start the engine and inspect the inside of the cab
Once the hood is closed the driver moves to the driver seat, starts the engine and checks gauges, controls and warning devices before going any further.
-
22. You are entering a freeway from a short ramp with a fully loaded trailer. What should you do?
Show answer
Answer A: Begin building speed early and wait for a large gap
A loaded vehicle accelerates slowly, so it needs both a running start and a much larger gap than a car would use.
-
23. Which of these is a major cause of skids in heavy vehicles?
Show answer
Answer C: Over-braking, over-steering, over-acceleration or driving too fast for conditions
Skids happen when the tires are asked for more grip than the road can give, which happens through braking, steering or accelerating too hard or simply too much speed.
-
24. A load overhangs the rear of the trailer. What must the driver check before leaving?
Show answer
Answer D: That the overhang is marked as required, with flags or lamps as conditions demand
A projecting load has to be made visible to other drivers, with flags in daylight and lamps when lights are required, so nobody runs into what they cannot see.
-
25. Which steering system findings count as defects during the inspection?
Show answer
Answer C: Bent, loose or broken column parts, arms, drag links or tie rods, and missing nuts, bolts or cotter keys
Every joint and fastener between the steering wheel and the tires carries the driver commands, so looseness or a missing retainer can end in a complete loss of steering.
-
26. Besides allowing the move at all, what does an oversize load permit usually set out?
Show answer
Answer C: The route to be followed, the hours of travel allowed and the warning equipment needed
Permits for oversize movements normally name the roads that may be used, restrict the times of travel, and list the flags, signs and escorts required.
-
27. What is the first step of the standard seven-step vehicle inspection?
Show answer
Answer C: A general overview of the vehicle, including the last inspection report
The routine opens with a walk-up overview of the vehicle and a review of the previous inspection report so known defects are addressed first.
-
28. As a long vehicle goes around a corner, how do the rear wheels travel compared with the front wheels?
Show answer
Answer A: They follow a tighter path, closer to the inside of the turn
The rear wheels off-track toward the inside of the turn, and the longer the vehicle the bigger the difference, which is why the front must swing wide enough to keep the rear off the curb.
-
29. With the tractor coupled to the trailer, what should you see between the upper and lower fifth wheel plates?
Show answer
Answer A: No space at all between the two plates
Any daylight between the plates means the trailer is not properly seated on the fifth wheel and the coupling can come apart under load.
-
30. Why can an empty truck need a longer stopping distance than a loaded one?
Show answer
Answer C: An empty vehicle has less traction, so its wheels lock up more easily
Brakes and tires are designed for a loaded vehicle, and with little weight on the axles the tires grip less and lock sooner.
-
31. What must a written driver vehicle inspection report cover at the end of the day?
Show answer
Answer C: Any defect or deficiency that would affect safety or could cause a mechanical breakdown
The report identifies the vehicle and lists defects that affect safe operation or could lead to a breakdown, so they are repaired before the next trip.
-
32. What should you do before backing into a space you have not used before?
Show answer
Answer A: Get out and walk around to check the path, the clearance and any obstacles
Walking the area first reveals low obstructions, soft ground and objects that never appear in the mirrors.
-
33. What actually lowers the amount of alcohol in the bloodstream?
Show answer
Answer B: Time
The liver removes alcohol at a fixed rate, so nothing but the passage of time reduces blood alcohol concentration.
-
34. Why must you never coast down a hill in neutral or with the clutch pushed in?
Show answer
Answer C: You lose the braking effect of the engine and your brakes may overheat and fail
Engine braking is what keeps a heavy vehicle in check on a grade; coasting throws it away and leaves the service brakes to do all the work until they overheat.
-
35. What should a driver assume about the height posted at a bridge or an overpass?
Show answer
Answer B: That it may be wrong, because repaving or packed snow can leave less clearance than the sign shows
Resurfacing and packed snow raise the road under the structure, so the real clearance can be lower than the posted figure.
-
36. During a trip you stop for a break. Which items should you check before driving on?
Show answer
Answer B: Tires, wheels and rims, brakes, lights, reflectors, electrical connections and cargo securement
Critical items can change during a trip, so each stop is used to recheck the tires, wheels, brakes, lights, connections and cargo.
-
37. What does a front-end header board on a van or flatbed protect against?
Show answer
Answer A: Cargo moving forward toward the cab in a crash or hard stop
The header board, often called a headache rack, blocks forward movement of the load toward the driver.
-
38. How do you avoid the sharp lurch that comes at the very end of a stop in a heavy vehicle?
Show answer
Answer A: Ease off the brake pressure just before the vehicle actually comes to rest
A smooth stop is finished by reducing pedal pressure as the vehicle settles, so the suspension does not rock the cab and the load forward.
-
39. How is a Pennsylvania anti-texting violation recorded for a commercial driver, compared to a non-commercial driver?
Show answer
Answer B: It is recorded as a non-sanction violation rather than adding points, unlike the non-commercial no-points outcome
A Pennsylvania anti-texting violation is recorded as a non-sanction violation for a commercial driver, while it adds no points at all for a non-commercial driver.
-
40. What blood alcohol concentration disqualifies the holder of a commercial driver license who is operating a commercial vehicle?
Show answer
Answer D: 0.04 or higher
Commercial drivers are held to 0.04, half the limit that applies to a driver of a passenger car in the same state.
-
41. After starting the engine, how quickly should the oil pressure gauge come up to its normal range?
Show answer
Answer B: Within a few seconds
Oil pressure should build within seconds of starting; if it stays low, the engine is not being lubricated and should be shut down.
-
42. How much free play in the steering wheel is enough to make a vehicle hard to steer and should be reported?
Show answer
Answer B: More than 10 degrees, roughly 2 inches of movement at the rim of a 20 inch wheel
Excess play means steering input is lost before the wheels respond, and more than about 10 degrees is treated as a defect.
-
43. Why should a driver avoid traveling alongside another vehicle for any length of time?
Show answer
Answer D: You lose your escape route and you may be sitting in the other driver blind spot
Running beside someone leaves nowhere to move if you have to change lanes, and the other driver may not know you are there at all.
-
44. You normally pull an empty trailer, but today the same tractor is loaded to its legal maximum. What changes about getting under way?
Show answer
Answer A: You may need to start in a lower gear, since the load takes more pulling power
The heavier the load, the lower the gear needed to get the vehicle rolling without lugging or stalling the engine.
-
45. During the vehicle overview, what should the driver look for on the ground under the vehicle?
Show answer
Answer B: Fresh puddles of oil, coolant, grease or fuel
New stains on the ground are the earliest sign of a leak, so the overview includes a look underneath before anything is opened or started.
-
46. What do you check about the fire extinguisher during the pre-trip?
Show answer
Answer C: That it is securely mounted, charged and that you know how to operate it
An extinguisher must be held in its bracket, show a charged gauge and be understood by the driver, because a fire leaves no time to learn.
-
47. A dock crew loads all of the freight at the very back of a 48 foot van trailer. What are the two consequences?
Show answer
Answer A: The steering axle is relieved of weight and steering becomes light, and the trailer axles may go over the limit
Weight placed far to the rear lifts weight off the front of the combination, so the steering goes light while the trailer axles take too much of the load.
-
48. Your brakes have failed and you decide to use the parking brake to slow down. Why should you hold the release button or lever while doing so?
Show answer
Answer D: So you can release the brake at once if the wheels lock and the vehicle starts to skid
The parking brake can lock the wheels; keeping your hand on the release lets you let go the moment a skid starts and regain control.
-
49. You are strapping down a load with sharp metal edges on a flatbed. What should you use?
Show answer
Answer D: Edge protection between the strap and the sharp edges so the tiedown is not cut
Sharp edges cut or wear through a strap under tension, so edge protectors are required wherever a tiedown could be damaged.
-
50. How should speed and gears be handled when approaching a curve?
Show answer
Answer A: Slow to a safe speed and downshift before entering the curve
Braking and shifting are completed before the curve so the vehicle is settled and can pull gently through it without upsetting the load.
-
51. What is a bulkhead in a cargo body used for?
Show answer
Answer D: To divide the space and stop cargo from moving into another part of the body
A bulkhead is a solid partition that separates one part of the load space from another and blocks the cargo from moving past it.
-
52. Besides slowing down, which technique most reduces the risk of a skid on a snow covered road?
Show answer
Answer B: Make every steering, braking and speed change gradual
Traction is limited on snow, and sudden inputs demand more grip than the surface can supply, so smoothness is what keeps the tires attached to the road.
-
53. How many questions are on the Pennsylvania school bus endorsement knowledge test?
Show answer
Answer B: 25
Pennsylvania uses 25 questions for the school bus endorsement test, compared with 20 for the passenger, tank and doubles or triples endorsements and 30 for hazardous materials.
-
54. Why should you never back under a trailer whose landing gear is resting on soft or muddy ground?
Show answer
Answer C: The landing gear can sink or collapse and the trailer can drop or tip over
Soft ground lets the landing gear sink under the load being transferred to it, and a trailer that drops or topples during coupling is extremely dangerous.
-
55. Why is braking while in a curve dangerous in a heavy vehicle?
Show answer
Answer A: The wheels lock more easily and the vehicle can skid
Tires already using their grip to turn have little left for braking, so hard braking in a curve locks the wheels; slow down before the curve instead.
-
56. The only way into a customer yard forces you to back toward the right, or blind, side of the vehicle. What should you do?
Show answer
Answer D: Use a helper and get out to check the path more often than you normally would
Blind side backing is allowed but far riskier, so it calls for a spotter you can see and for repeated checks of the path on foot.
-
57. Federal rules require a power unit that is not carrying placarded hazardous materials to have a fire extinguisher with which minimum rating?
Show answer
Answer A: One rated 5 B:C or more, or two rated 4 B:C or more each
The minimum is a single unit rated 5 B:C or more, or two units of at least 4 B:C each, which is enough to attack a fuel or electrical fire.
-
58. What is the minimum tread depth required in every major groove of a steering axle tire?
Show answer
Answer D: 4/32 inch
Federal rules set a higher tread minimum for front steering tires than for other positions because a steering tire failure is far harder to control.
-
59. How are the headlights, marker lights and turn signals checked during the seven-step inspection?
Show answer
Answer A: The engine is shut off, the parking brake is set, the lights are switched on and then checked from outside the vehicle
The lights are switched on with the vehicle secured, then the driver walks around and confirms each lamp actually works and is clean.
-
60. Which combination of warning devices meets the requirement for a stopped commercial vehicle?
Show answer
Answer A: Three reflective triangles, or six fusees, or three liquid burning flares
A vehicle may carry three bidirectional reflective triangles, six fusees or three liquid burning flares as its warning devices.
-
61. You are about to cross a long, high bridge with a light load in gusty wind. What should you do?
Show answer
Answer C: Slow down and be ready for a sudden push
Wind is strongest where a bridge leaves the shelter of the land, and lower speed gives you time to correct when the first gust hits.
-
62. How does a front tire failure usually feel to the driver?
Show answer
Answer D: The steering suddenly becomes heavy and pulls to one side
A failed front tire loads the steering and makes the wheel feel heavy, while a rear tire failure shows up as the back end swaying.
-
63. In dense city traffic you cannot see 12 seconds ahead because other vehicles block the view. What is the best response?
Show answer
Answer A: Slow down and open up more space in front of you
When you cannot see far enough ahead, extra following distance buys back the reaction time that the blocked view has taken away.
-
64. You are taking a tightly curved highway exit ramp in a long combination. Where should the tractor be placed within the lane?
Show answer
Answer D: Toward the outside of the curve, leaving room for the trailer to track inside
Because the trailer wheels cut to the inside of the curve, the tractor has to be kept out toward the outer edge so the trailer does not drop a wheel off the inside edge.
-
65. What does the suspension system weight rating tell the driver?
Show answer
Answer A: The maximum weight that the manufacturer says the suspension can carry
Like tires and axles, suspensions have a manufacturer capacity, and loading beyond it can damage springs and air bags.
-
66. A doctor prescribes you a medicine that can cause drowsiness. What should you do?
Show answer
Answer A: Tell the doctor what you drive and not drive while affected
Both prescription and over the counter medicines can make a driver unsafe, so the medical professional must know the job and the driver must stay out of the seat while affected.
-
67. Which items belong to the in-cab part of the inspection?
Show answer
Answer D: Gauges, controls, mirrors, windshield, wipers, horn, heater and defroster
The in-cab step checks the instruments and controls the driver depends on, along with mirrors, glass, wipers, horn and the heater and defroster.
-
68. An unblocked article is 15 feet long. What is the minimum number of tiedowns?
Show answer
Answer B: Three
Two tiedowns cover the first 10 feet and one more is added for each further 10 feet or any part of it, so 15 feet needs three.
-
69. When is a road surface usually most slippery during a rain shower?
Show answer
Answer A: Just after the rain starts, when water mixes with oil and dirt on the surface
The first rain lifts oil and dust into a slick film that has not yet been washed away, so the road is more slippery than it will be later.
-
70. Why is driving much slower than the rest of the traffic dangerous?
Show answer
Answer B: Other drivers must keep passing you, which creates conflicts
Traffic that has to work its way around you produces lane changes and closing speeds, which is why a large speed difference is itself a hazard.