Pennsylvania PennDOT CDL General Knowledge Practice Test 1
Test 1 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 56 correct answers to pass, the same ratio as the real Pennsylvania test.
- Questions70
- Correct to pass56
- Passing score80%
- Minimum age18 years
-
1. You are inspecting the vehicle alone and need to confirm that the stop lights work. Which method is correct?
Show answer
Answer A: Have a helper press the brake pedal, or apply the brake in a way that keeps it on while you check from outside
Stop lights are checked from outside the vehicle while the brakes are applied, so a helper or a brake held on is needed.
-
2. In hazard perception, what counts as a hazard?
Show answer
Answer C: Any road user or condition that could become a danger
A hazard is anything with the potential to create danger, which is why drivers are taught to spot them early rather than react to emergencies.
-
3. An enforcement officer inspects your vehicle at the roadside and attaches an out-of-service sticker. What may you do?
Show answer
Answer C: Nothing until the defect is repaired; the vehicle may not be driven
An out-of-service order means the vehicle is unsafe, and no schedule, load or destination allows it to be driven before the defect is corrected.
-
4. The rear wheels of your vehicle lock during braking and the rear starts to slide sideways. What should you do first?
Show answer
Answer A: Stop braking so the rear wheels can roll again, then steer quickly in the direction you want to go
Locked wheels have no side grip; releasing the brakes restores traction and then countersteering brings the vehicle back into line.
-
5. Your brakes have failed on a downgrade and there is no escape ramp in sight. What is the best choice?
Show answer
Answer A: Steer into an open field or onto a side road that flattens out or climbs uphill
A flat or uphill escape route uses gravity and rolling resistance to stop the vehicle; take it as soon as you see it, because the longer you wait the faster you go.
-
6. A straight truck has a long body behind the rear axle. What happens to that overhang in a sharp left turn?
Show answer
Answer D: It swings out to the right and can strike a vehicle or an object on that side
Body that hangs behind the rear axle swings the opposite way to the turn, so the tail of the truck sweeps out into the next lane or over the curb.
-
7. Besides the hours when the law requires them, when should headlights be switched on?
Show answer
Answer A: Any time visibility is poor, such as in rain, fog or at dusk
Headlights are used to be seen as much as to see, so they belong on whenever light or weather makes the vehicle harder to spot.
-
8. You are moving an oversized load under a permit that requires a pilot vehicle. What is the pilot vehicle there to do?
Show answer
Answer B: Warn other traffic and check the route ahead for clearances and hazards
Escort or pilot vehicles warn approaching traffic and scout the route for low bridges, narrow spots and other hazards that a wide or long load cannot pass.
-
9. What must a Pennsylvania vehicle required to stop at railroad crossings display on its rear?
Show answer
Answer C: A sign stating that the vehicle stops at railroad crossings
A vehicle that is required to stop at railroad crossings must display a rear sign stating that it stops at railroad crossings, so following drivers are warned in advance.
-
10. You drive a 40 foot straight truck at 50 miles per hour in good conditions. What following distance does the rule of thumb call for?
Show answer
Answer A: 5 seconds
One second for every 10 feet of vehicle length gives 4 seconds, and one extra second is added for speeds above 40 miles per hour.
-
11. What is the main purpose of a retarder fitted to a heavy vehicle?
Show answer
Answer B: To help slow the vehicle and reduce the need to use the service brakes
Exhaust, engine, hydraulic and electric retarders all slow the vehicle so the brakes stay cool and wear less, especially on grades.
-
12. Your right wheels drop off the pavement onto a soft shoulder. What is the correct recovery?
Show answer
Answer A: Stay on the shoulder, ease off the accelerator, brake gently only once speed is down to about 20 mph, then steer back sharply and countersteer at once
Bringing speed down on the shoulder first avoids a violent sideways jolt, and countersteering the instant the tires are back on the pavement keeps the vehicle out of the next lane.
-
13. Total stopping distance is made up of which parts?
Show answer
Answer A: Perception distance, reaction distance and braking distance
The vehicle travels while the hazard is recognized, while the driver moves to the pedal, and again while the brakes slow the vehicle.
-
14. Which of these is a suspension defect you must look for during the walkaround?
Show answer
Answer D: Cracked or broken spring leaves, loose or broken U-bolts, or leaking air suspension bags
Broken springs, failed U-bolts and leaking air bags let the axle shift or the body drop, which can make the vehicle impossible to control.
-
15. Why should the radio, the fan and other noisy equipment be switched off during a required stop at a railroad crossing?
Show answer
Answer C: So that an approaching train can be heard
The rules require the driver to look and listen along the track, and on a double track crossing a passing train can hide a second one, so hearing matters as much as seeing.
-
16. You can see a crack in a brake drum that runs across more than half the width of the friction surface. What does this mean?
Show answer
Answer C: The drum is defective and must be repaired before the vehicle is driven
Cracks longer than half the width of the friction area mean the drum can break apart under braking heat and must be replaced.
-
17. What is the driver responsible for when a load is covered with a tarp?
Show answer
Answer C: Fastening it so it cannot flap free, block a mirror, or come off in the wind
A tarp that works loose can tear away, block the driver view or the view of others, and become a hazard for the traffic behind.
-
18. When should a lower gear be selected for a long downgrade?
Show answer
Answer D: Before you start down the hill
The gear is chosen at the top, while speed is still low, because a heavy vehicle already rolling fast may not go into a lower gear at all.
-
19. What is the purpose of blocking placed against cargo on a trailer deck?
Show answer
Answer B: To fill the space around the cargo so it cannot slide
Blocking is shaped to fit snugly against the cargo and fastened to the deck, removing the room the load would need in order to move.
-
20. For a modern truck with low-friction parts and a streamlined shape, which gear should be used going down a grade?
Show answer
Answer D: A gear lower than the one needed to climb the same grade
Newer trucks roll more freely than older ones, so the old rule of using the climbing gear no longer holds; a lower gear is needed for enough engine braking.
-
21. Why is a leaking exhaust system on a commercial vehicle dangerous to the driver?
Show answer
Answer B: It can let carbon monoxide reach the cab, where it can poison the occupants
Exhaust gas contains carbon monoxide, which has no smell and dulls the driver judgment long before it becomes obvious that anything is wrong.
-
22. How does overloading affect the way a vehicle drives?
Show answer
Answer C: It slows the vehicle on upgrades, makes stopping take longer and can overheat the brakes on downgrades
Extra weight demands more from the engine and the brakes, so the vehicle climbs slowly and needs much more distance to stop.
-
23. How does a driver measure following distance in seconds?
Show answer
Answer A: Wait for the vehicle ahead to pass a fixed roadside object, then count the seconds until the front of your vehicle reaches the same object
Counting from the moment the vehicle ahead passes a landmark until you reach it turns a gap you cannot judge in feet into a number of seconds.
-
24. Your axle weights are legal, but the tires on that axle are rated below the weight it is carrying. What controls?
Show answer
Answer B: The lower figure, so the tires may not be loaded beyond their marked rating
You may never exceed the rating marked on a tire, even when the axle limit would allow more, because an overloaded tire builds heat and can fail.
-
25. An article of cargo has been blocked so that it cannot move forward. How many tiedowns does the federal rule call for?
Show answer
Answer A: One tiedown for every 10 feet of article length, or any part of that
Blocking against forward movement lowers the requirement to one tiedown per 10 feet of length or fraction of 10 feet.
-
26. Which Pennsylvania farming operation is exempt from the commercial driver license requirement?
Show answer
Answer A: A farm vehicle controlled by a farmer and used exclusively to carry agricultural products, farm machinery or farm supplies within 150 miles of the farm
Pennsylvania exempts a farm vehicle controlled and operated by a farmer and used exclusively to transport agricultural products, farm machinery or farm supplies within 150 miles of the farm.
-
27. You have just passed another vehicle on a two lane road. What tells you it is safe to return to your lane?
Show answer
Answer B: You can see the whole front of that vehicle in your right mirror
Seeing the entire front of the vehicle you passed in your mirror proves you are far enough ahead to move back over without cutting the driver off.
-
28. What does safe practice require of a commercial driver who wants to eat, drink or read a delivery note?
Show answer
Answer B: Handle it before or after driving, not while moving
Anything that takes hands, eyes or attention away from the task belongs outside the driving time, not inside it.
-
29. You are about to slow down sharply on a highway to make a turn into a narrow driveway. How can you warn the drivers behind you?
Show answer
Answer C: Tap the brake pedal a few times so the brake lights flash before you slow down
A few light taps flash the brake lights and give following drivers an early warning that you are about to slow or stop.
-
30. After the first inspection of a trip, how often must cargo securement be checked again?
Show answer
Answer D: Every 3 hours or 150 miles or at each change of duty status, whichever happens first
The load must be re-checked at whichever of those points arrives first, so a loosening tiedown is found long before it fails.
-
31. A commercial vehicle stops on the shoulder of a one-way or divided highway. Where do the three warning devices go?
Show answer
Answer A: At 10 feet, 100 feet, and 200 feet back toward approaching traffic
Traffic arrives from one direction only, so all three devices are set back toward it at 10, 100, and 200 feet, and they must be out within ten minutes.
-
32. What frame defects are you looking for during the walkaround?
Show answer
Answer A: Cracks, bends or broken cross members
The frame carries the whole load, so cracked or bent rails and broken cross members are serious structural defects.
-
33. Besides staying secure, cargo carried inside a vehicle must not do what?
Show answer
Answer C: Block the driver view or access to emergency equipment and exits
Cargo may not obstruct the view to the front or sides or prevent the driver from reaching emergency equipment and exits.
-
34. Under the federal hours of service rules, when must a property-carrying driver take a 30 minute break?
Show answer
Answer C: After 8 cumulative hours of driving time
Driving is not allowed after 8 cumulative hours of driving time without at least a 30 consecutive minute interruption of driving.
-
35. What must be true of the trailer landing gear before you move off?
Show answer
Answer B: Fully raised, with the crank handle secured and no missing or damaged parts
Landing gear left part way down can strike a railway crossing or a ramp, and a loose crank handle can swing out into a passing vehicle.
-
36. What is the payload of a truck?
Show answer
Answer C: The weight of the cargo the vehicle is carrying, that is the loaded weight less the empty weight
Payload is what is left of the legal or rated weight once the weight of the empty vehicle is taken off, and it is the weight of cargo that can be carried.
-
37. You are loading a flatbed that has no sides or bulkheads. How must the cargo be held?
Show answer
Answer D: By tiedowns, blocking or bracing, since there are no walls to keep it from shifting or falling off
Open decks depend entirely on securement devices; every article must be tied down or otherwise immobilized so it cannot move, spill or fall.
-
38. You must leave the vehicle parked on a slight grade. What adds security beyond setting the parking brake?
Show answer
Answer D: Chocking the wheels so the vehicle cannot roll if the brake bleeds off
Chocks hold the vehicle mechanically and are the standard backup whenever a parked vehicle could roll.
-
39. You are stopped in a line of traffic behind a car. How much space should you leave in front of you?
Show answer
Answer C: Enough to see where the rear tires of that car meet the road
That amount of space lets you pull around the vehicle ahead if it stalls and absorbs some of the shock if you are struck from behind.
-
40. Using the snub braking method on a downgrade, when does the driver release the brakes?
Show answer
Answer A: After speed has dropped about 5 mph below the safe speed
The driver brakes firmly to about 5 mph under the chosen safe speed, releases to let the brakes cool, then repeats when the safe speed returns.
-
41. Why must the driver of a large vehicle keep it centered in its lane?
Show answer
Answer B: The vehicle needs the full width of the lane
A commercial vehicle is close to lane width already, so any drift takes part of the vehicle into the next lane or onto the shoulder.
-
42. You have stopped and a pedestrian is waiting to cross in front of your truck. Why should you not wave the person across?
Show answer
Answer C: Another driver may not stop, and your wave sends the person into danger
You cannot control what drivers in the other lanes will do, so you should not invite a pedestrian into a lane you do not command.
-
43. On the Interstate System, what are the federal maximums for a tandem axle group and for gross vehicle weight?
Show answer
Answer B: 34,000 pounds and 80,000 pounds
The federal Interstate limits allow 34,000 pounds on a tandem axle group and 80,000 pounds gross.
-
44. What must the motor carrier do about a defect listed on a driver vehicle inspection report?
Show answer
Answer D: Repair it, or certify that repair is not needed, before the vehicle is dispatched again
A reported defect must be corrected, or certified as not needing correction, and that certification is what the next driver reads before taking the vehicle.
-
45. When a helper guides you while backing, what should be agreed on before you start?
Show answer
Answer D: A set of hand signals, especially the signal that means stop
The driver and helper must agree on signals in advance, above all the stop signal, because they usually cannot hear each other.
-
46. Most rollovers of loaded trucks on exit and entrance ramps happen for which reason?
Show answer
Answer B: The ramp was taken faster than the load could tolerate
A posted ramp speed is set for cars, and a loaded trailer with a high center of gravity can roll at a speed a car would take easily.
-
47. What must be checked on a sliding fifth wheel during the inspection?
Show answer
Answer B: That it is locked in position and not so far forward that the trailer can hit the cab
A slider that is unlocked can move under braking, and one set too far forward lets the trailer strike the cab when the tractor turns sharply.
-
48. Where on the road are you most likely to find ice in cold weather?
Show answer
Answer B: On bridges, overpasses and shaded stretches, which freeze before the rest of the road
Bridges and overpasses lose heat from above and below, and shaded areas get no sun, so they ice over first and stay icy longest.
-
49. You want to check whether a tire on your truck is properly inflated. What is the correct method?
Show answer
Answer A: Measure the pressure with a tire gauge
Only a tire gauge tells you the actual pressure; a tire can look and sound normal while being badly underinflated.
-
50. Cargo carried inside the cab must never do which of these?
Show answer
Answer C: Block the driver view, restrict arm or leg movement, or block an emergency exit
Anything inside the cab must leave the driver a clear view, free movement of the arms and legs, and an unobstructed way out of the vehicle.
-
51. How do you confirm that the coupling is locked before pulling out of the yard?
Show answer
Answer D: By locking the trailer brakes and pulling gently forward against them
The tug test loads the coupling in the direction that would pull it apart, so if the jaws are not closed on the kingpin you find out at walking pace.
-
52. Why must exhaust components be checked for contact with other parts of the vehicle?
Show answer
Answer B: Hot exhaust parts touching fuel lines, tires or wiring can start a fire
Exhaust pipes run hot enough to ignite fuel and melt insulation, so they must be kept clear of the fuel system, the tires and the electrical harness.
-
53. What speed and gear should be used when backing a large vehicle?
Show answer
Answer B: As slowly as possible, in the lowest reverse gear
Backing slowly in the lowest reverse gear keeps the vehicle under precise control and leaves time to correct the path.
-
54. Why does the commercial driver manual tell you to look far down the road instead of only at the vehicle ahead?
Show answer
Answer D: So you can adjust smoothly instead of braking hard at the last moment
A heavy vehicle cannot react quickly, so early information lets you slow gradually rather than make a sudden stop or swerve.
-
55. How does the working load limit of a tiedown relate to the force that would break it?
Show answer
Answer B: The working load limit is a fraction of the breaking strength and is the figure you use
The working load limit is set well below the point at which the device would fail, and securement is always calculated from the working load limit, never from breaking strength.
-
56. A delivery van is stopped in the right lane ahead with its flashers on. What should you expect?
Show answer
Answer C: Someone may step into your lane from in front of it
A stopped delivery vehicle hides the space in front of it, and that is exactly where a person carrying a package is likely to walk out.
-
57. Why does a cracked frame rail or cross member make a vehicle unsafe?
Show answer
Answer B: The frame carries the whole load, and a crack can spread until the structure fails
The frame is the backbone that supports the body, the load and the running gear, so a crack in it is a structural failure that grows with every mile.
-
58. What are the rules for using your turn signal before a turn or lane change?
Show answer
Answer A: Signal early, keep the signal on until the turn is finished, then cancel it
An early, continuous signal tells others what you plan to do; cancelling afterward keeps the signal from misleading them.
-
59. An oncoming vehicle at night has bright headlights that are making it hard to see. What should you do?
Show answer
Answer B: Look toward the right edge of your lane and avoid looking directly at the lights
Looking at the right edge of the road keeps your eyes off the glare while you stay in your lane; glare can leave you nearly blind for several seconds.
-
60. How should the headlamps be checked during the pre-trip inspection?
Show answer
Answer A: By switching on both low beam and high beam and confirming each one works outside
Both beams are separate circuits, so each is switched on in turn and confirmed from outside the vehicle where the lamps can actually be seen.
-
61. What should be checked about the power steering system in the engine compartment?
Show answer
Answer D: That the fluid level is correct and the hoses and pump are not leaking
Losing power steering fluid means losing steering assistance, which can happen suddenly and makes a heavy vehicle very hard to turn.
-
62. Within total stopping distance, what exactly is perception distance?
Show answer
Answer D: The distance traveled from the moment your eyes see a hazard until your brain identifies it
Perception distance covers only the time between seeing a hazard and recognizing it as a hazard, before any physical reaction begins.
-
63. On a set of dual tires, which condition must be reported as a defect?
Show answer
Answer D: The two tires are touching each other or rubbing on part of the vehicle
Duals that touch each other or the vehicle overheat and wear quickly, so they must be separated by proper spacing and inflation before driving.
-
64. The paperwork shows a weight, but the load looks heavier than you expected. What should you do?
Show answer
Answer C: Weigh the vehicle, since you are the one answerable for driving it overweight
The driver is the one who can be cited for an overweight vehicle, so a doubtful weight is settled on a scale before the trip continues.
-
65. Which parts of total stopping distance can a driver shorten simply by staying alert and looking far ahead?
Show answer
Answer B: Perception distance and reaction distance
Alertness shortens the time spent recognizing a hazard and moving your foot to the pedal; braking distance depends on speed, weight, brakes and the road surface.
-
66. You need to pull off onto the shoulder because of a problem with the load. How should you communicate that to other drivers?
Show answer
Answer D: Signal the move, then switch on the four-way flashers once stopped
Other drivers need a signal before you leave the lane and a clear warning once the vehicle is stopped near the traffic lanes.
-
67. What should you check about the air hoses and the electrical cord running to the trailer?
Show answer
Answer D: That they are free of damage, properly connected and not dragging or rubbing
Lines that chafe on the frame or drag on the road wear through, and a broken line takes away trailer braking or trailer lighting without warning.
-
68. Which lamp must make the rear registration plate legible after dark?
Show answer
Answer C: A white lamp that lights the plate
A white license plate lamp is required so the plate can be read at night, and a burned out one is a defect like any other lamp.
-
69. A fire has started in the vehicle. How should the extinguisher be used?
Show answer
Answer B: Stay as far back as the reach of the extinguisher allows, stand upwind, and aim at the base of the fire
Aiming at the base attacks what is actually burning, and staying upwind and well back protects the driver from heat, smoke and the flames themselves.
-
70. Which wheel or rim condition must be treated as a defect during the walkaround?
Show answer
Answer C: Cracks, illegal welded repairs, or missing and loose lug nuts
Cracked or welded rims and missing or loose fasteners can let a wheel separate from the vehicle and must be corrected before driving.